Full Version: Doming - testing the waters.
From: Ken D. (KDEVORY) [#60]
8 Apr 2005
To: Barbara (RGILE) [#59] 12 Apr 2005
My box is working well for me. Do you have any idea what the nail curer cost, or where to get them. Others may be interested, who don't want to wire up their own box.
From: GBengraver [#61]
8 Apr 2005
To: Rodney Gold (RODNEY_GOLD) [#39] 8 Apr 2005
Is the 2 part resin readily available?
Do you need to special order them from a wholesaler?
Is odor an issue with either method?
From: Rodney Gold (RODNEY_GOLD) [#62]
8 Apr 2005
To: GBengraver [#61] 15 Apr 2005
Its easilky available , I live in african country , South africa and I have multiple sources here , so I hardly doubt that in the USA it would be even easier to get.
We have no issues with it odor or irritant wise , our applicator ladies wear gloves and safety glasses , prolonged contact can cause irritations and they arent really such great stuff to work with , having all sorts of horrible sounding chemical names in em like isocyantes - I tend to think anything with cyanide in its name (or any derivative of) is probaly a little nasty.
It will definately irritate your eyes if you get it into them.
You can try it real easy by getting a dispenser type gun and carts , lots of doming suppliers keep it , a local search for 2 part water clear resin or urethane doming , epoxy doming etc should bring a few names up
If you want to use bulk and get the benefits of the much cheaper price , you need a mixer and dispenser which can cost at least $2k or more
From: Barbara (RGILE) [#63]
12 Apr 2005
To: Ken D. (KDEVORY) [#60] 12 Apr 2005
Hi Ken,
I got mine from a Hairdressing supplier. They run around 100.00 and the material is nail acrylic and is also the same stuff that dentist's use for bonding teeth. So a dental supplier would also be a good avenue for the acrylic. After it's cured it leaves a sticky surface that is taken off with a soulotion of alcohal. so I hope this helps a little.
It's would be good for small jobs.
Barbara
From: lisa (LISASANDERS) [#64]
2 May 2005
To: Stunt Engraver (DGL) [#13] 2 May 2005
Hi David...
My husband and I attended the sublimation class at Coast Graphics on April 9th and saw you there. We were very impressed with your work - Fantastic stuff!
We purchased the doming epoxy while there and have just tried it out for the first time on a photograph. It didn't adhere to the photo. Can you tell us why? It looked great - no bubbles, shiny, etc. - but it didn't stick. What materials can we dome on? Evidently not photographs? I'm going to try it on a name badge next and am assuming it will turn out just fine.
Thanks for your help....
From: Ken D. (KDEVORY) [#65]
2 May 2005
To: lisa (LISASANDERS) [#64] 2 May 2005
Lisa,
It depends on the "paper" and the ink. Yes you can dome photos, sometimes.
First test the paper without the photo. It won't stick to HP premium plus photo glossy, but will stick to my ordinary office paper. It also sticks to some polyester paper I have. According to some other posts its due to UV inhibitors in some papers and inks. They leach into the epoxy forming a thin layer that won't cure. -I'm assuming you're using UV cure epoxy.
I also found that I need to dry out the ink. There's an old stove here with a pilot light. during my testing with small photos I put them on a piece of glass on the stove top above the pilot. For production I'd try some of the other suggestions made.
From: Stunt Engraver (DGL) [#66]
2 May 2005
To: lisa (LISASANDERS) [#64] 2 May 2005
Hi Lisa,
It was nice to meet you at the CGS "Learning Center" event. I'm happy to hear you're taking the plunge into epoxy doming.
The fact that some substrates don't lend themselves to doming, has been covered, either in this thread or another. I'm not sure which.
The short story is, some paper/ink combinations don't work. You're experiencing that for yourself.
What substrate are you using for the namebadge? Metal and plastic should be fine. If you're using a paper, it will probably need to be poly-based.
If you use a paper, make sure your ink is completely dry before doming.
EDITED: 2 May 2005 by DGL
From: lisa (LISASANDERS) [#67]
3 May 2005
To: Stunt Engraver (DGL) [#66] 3 May 2005
From: lisa (LISASANDERS) [#68]
3 May 2005
To: Ken D. (KDEVORY) [#65] 3 May 2005
From: Stunt Engraver (DGL) [#69]
3 May 2005
To: lisa (LISASANDERS) [#67] 3 May 2005
Lisa,
I'm happy to hear you're enjoying the forum. It's become my labor of love.
I'm pleased, the posts are so frequent and informative, but the best is yet to come!
Do you know the differences between CO2 and YAG laser engraving?
Do you know the difference between "Flying Optics" and "Steered Beam" laser equipment?
Have you ever been behind the scenes at a high-production YAG laser engraving facility?
If not, you will!
We're in the formative stages of developing our first "Video Field Trip", which will be made available to the forum members!
ÂÂÂÂÂ
EDITED: 3 May 2005 by DGL
Show messages: 1-19 20-39 40-59 60-69