Full Version: Need hot stamping done
From: Don (DONFORD) [#1]
15 Apr 2005
To: ALL
Good mornng,
I am new to your board, recommend by a member.
I have someone looking at a part that we need hot stamped and IF they aren't able to do it, is there anyone here who would be interested?
The company I work for has some Polycarbonate dials with the numbers and indices marks raised very little. The dial is 3" in diam. and the numbers etc. are about 2 3/4" in Diam. It is about 3/8" thick.
We used to do our own hot stamping but our machine broke down and they took the stamping off of everything but this part. It will take a flat heat plate to stamp them. We can furnish the holding fixture but it is about 2 inches tall. We can also furnish the foil.
If there is anyone who wold be interested, please let me know and if you want to talk to me about it, call me at 800-872-7832, ext. 195 or email dford@s-tec.com . I will be here weekdays until about 3:00 PM, CST, or you can email me at home after hours or on the weekends at donford@cox.net.
From: Engravin' Dave (DATAKES) [#2]
15 Apr 2005
To: Don (DONFORD) [#1] 15 Apr 2005
Don,
Where are you located?
From: trophyman (MIKEBERGER) [#3]
15 Apr 2005
To: Don (DONFORD) [#1] 15 Apr 2005
Where are you located?
I am near Rockford, Il. and could possibly do them for you.
(815) 986-7374 till 3pm CST
after 4pm (815) 561-1221.
Mike Berger
From: Don (DONFORD) [#4]
15 Apr 2005
To: trophyman (MIKEBERGER) [#3] 16 Apr 2005
From: LaZerDude (C_BURKE) [#5]
15 Apr 2005
To: Don (DONFORD) [#4] 15 Apr 2005
Don,
Check with Roy Brewer of Brewer sales.... roy@brewersales.com He is in Arlington Texas. If he cannot do it for you, he will know somone that can...
From: Don (DONFORD) [#6]
15 Apr 2005
To: LaZerDude (C_BURKE) [#5] 16 Apr 2005
From: LaZerDude (C_BURKE) [#7]
16 Apr 2005
To: Don (DONFORD) [#6] 16 Apr 2005
HI Don,
Roy and his daughter Jeanette are both members of this and other forums as well. I just figured if you were in Texas and they were in Texas it might be a good logisitical fit.
From: Don (DONFORD) [#8]
16 Apr 2005
To: LaZerDude (C_BURKE) [#7] 16 Apr 2005
From: Pedaler (ROYBREWER) [#9]
18 Apr 2005
To: Don (DONFORD) [#1] 18 Apr 2005
Don,
I got your email message and responded before I perused this forum. In case you read this b4 checking your email, I forwarded a few options.
From: Don (DONFORD) [#10]
18 Apr 2005
To: Pedaler (ROYBREWER) [#9] 18 Apr 2005
Great Roy. I will read them in the morning when I get to work. I appreciate it. Can you send me your phone number to the email addy I emailed you from so I can call tomorrow and talk to you about it? Have a BLESSED evenig.
God Bless You
Don
From: Don (DONFORD) [#11]
26 Apr 2005
To: Don (DONFORD) [#10] 26 Apr 2005
I got a phone call from a man up north and he was going to send me his info but haven't received it yet. If you are reading this, please let me know. He said a man here had told him about me needing these stamped. Please contact me at either email below or call me at
800-872-7832, ext. 195 (CST)
Work, dford@s-tec.com
Home donford@cox.net
Thank you
Don