Full Version: Elec. panel tag pricing?

From: sroehlk (ELECTECH1) [#3]
 2 Apr 2007
To: wolvey (JIMH) [#1] 2 Apr 2007

BTW-

I don't see what type of equipment your using in your profile. That would help with answers!

Do you have rotary equipment, manual or computerized, and what size table?

From: Bob (BOBKEYES) [#4]
 2 Apr 2007
To: wolvey (JIMH) [#1] 2 Apr 2007

Jim,

I do a lot of legend plates and tags for electrical panels. I charge $3.00 for 22.5mm legends and $3.50 for 30mm. The Jumbo's go for $4.50. Tags run anywhere from $1.50 up to $10.00 for a 4 x 8.

I use Romark from Johnson Plastics with the adhesive already applied. I start with a 24" 24" sheet and engrave first. Then cut the inner circle and then cut the outside. I space my tags .25mm apart. You can do them against each other, but I find that the finish on the adjacent tag suffers some.

I cover the Romark with transfer tape. Now the hard part. Weeding the tape off.

By the way, most on the forums say to remove the protective plastic before putting on the tape. I have never remove it and have never had any kind of problem related to it.

Peel the tape and let them sit over night and the "sticky" is gone. If you're pushed you can remove the sticky with most any cleaner.

Good luck.

From: Harvey only (HARVEY-ONLY) [#5]
 2 Apr 2007
To: Bob (BOBKEYES) [#4] 2 Apr 2007

I have been told that the easy way to weed tiny spots like letter centers is to apply a high stick tape, like duct tape, then peel it off with all of the pieces stuck to it.

From: Tony (ANTE) [#6]
 2 Apr 2007
To: wolvey (JIMH) [#1] 2 Apr 2007

Jim,
Legend plates and full panel layouts is 95% of our work.
Prices are $3.00 for standard plastic legends (any color) that we cut in house either with laser or rotary if beveled edge is requested.
Aluminum we buy ready made but not from electrical distributors,
they are to costly. I am sure you can get them from RONP.
Aluminum legends we charge $3.50 standard, jumbo once 4.50
I have found supplier for 22.5 MM legends black laser aluminum for $0.55each on 100 piece quantity.
Tony

From: Bob (BOBKEYES) [#7]
 2 Apr 2007
To: Harvey only (HARVEY-ONLY) [#5] 2 Apr 2007

Thanks Harvey. I'll try that for sure. In fact I'll try that tonight.

Thanks again.

From: wolvey (JIMH) [#8]
 2 Apr 2007
To: ALL

Thanks for all the great info gang. Especially thanks to Steve, Bob and Tony. This is exactly what I was hoping for. BTW- Steve thanks for the heads up on my profile. Something must have happened because I did have it filled out originally. I will re do it. But for equipment, primarily my main equipment is a Xenetech XLT 1325 45 watt laser. No rotary right now. Again thanks guys. -Jim H. Amazing Engraving

From: Ron (RONRUSH) [#9]
 3 Apr 2007
To: ALL

I'm curious to know what these legends look like?????? Anybody have any photos???? Thanks.

From: Stunt Engraver (DGL) [#10]
 3 Apr 2007
To: Ron (RONRUSH) [#9] 3 Apr 2007

Ron,

Here's are some examples of legend plates.

http://www1.mscdirect.com/CGI/N2DRVSH?PMSECT=2009362

EDITED: 3 Apr 2007 by DGL

Show messages: All  1-2  3-10

Back to thread list | Login

© 2025 Project Beehive Forum