Full Version: Epilog problem
From: Rose (RSLIEPKA) [#4]
15 Apr 2007
To: Epilog_Laser (PECK_SIDARA) [#3] 15 Apr 2007
Thank You SO much.
I will run over to the shop and follow your instructions.
We are doing a welcome home for two soldiers at 2-3pm Ca. time but I will get back to you.
THANK YOU
From: Rose (RSLIEPKA) [#5]
15 Apr 2007
To: Epilog_Laser (PECK_SIDARA) [#3] 15 Apr 2007
Thank you, Everything worked like you said!
There were two nuts and one allen (someday I would like to meet the person who designed that allen screw in that location) but other than that everything matched exactly. Just the side with the motor was jammed. Got that loose, put everything back together and seems to be working fine.
By the way, what was the best way to get the cans out once I got the table level? I was afraid to leave them in until I turned it on and checked it just in case.
I can't tell you how much I appreciate your help today. Your willingness to help is one of the biggest reasons I bought an Epilog.
Thanks,
Rose
By the way, what would have caused the one side to jam?
From: UncleSteve [#6]
15 Apr 2007
To: Rose (RSLIEPKA) [#5] 15 Apr 2007
If you had used two beer cans instead of soda and emptied them prior to doing the repair, you would have been able to squeeze them in the middle and the cans would collapse and get shorter... ;-)
From: Rose (RSLIEPKA) [#7]
15 Apr 2007
To: UncleSteve [#6] 15 Apr 2007
From: Epilog_Laser (PECK_SIDARA) [#8]
15 Apr 2007
To: Rose (RSLIEPKA) [#5] 15 Apr 2007
Rose,
I'm glad you got it worked out. To remove the cans, you could've just booted the machine after everything was put back together, from there, raise the table from the display. The table can get jammed for a few different reasons, the most common one is auto-focusing on the vector grid. Another would be auto-focusing with a faulty auto-focus plunger tip. Have a nice day.
Regards,
From: Boz (CHEDDARHEAD) [#9]
15 Apr 2007
To: ALL
Peck, who said you were just another salesman? Nice job.
Glad to hear it worked out Rose.
EDITED: 15 Apr 2007 by CHEDDARHEAD
From: Peck.Sidara (LAOPADAK) [#10]
15 Apr 2007
To: Boz (CHEDDARHEAD) [#9] 16 Apr 2007
From: jeanettebrewer (JEANETTEBREWER2) [#11]
15 Apr 2007
To: Boz (CHEDDARHEAD) [#10] 16 Apr 2007
Yes, Boz, thanks for jumping in and helping. I know you've been very busy with your top secret nefarious plot ...
How DO you find the time?
From: Boz (CHEDDARHEAD) [#12]
16 Apr 2007
To: ALL
From: JHayes55 [#13]
16 Apr 2007
To: Boz (CHEDDARHEAD) [#12] 16 Apr 2007
–adjective
extremely wicked or villainous; iniquitous: a nefarious plot.
[Origin: 1595–1605; < L nefÄÂrius wicked, vile, equiv. to nefÄÂs offense against divine or moral law (ne- negative prefix + fÄÂs law, right) + -ius -ious, with intervocalic s> r]
Gee - what a great term to have hung on you.