Xenetech Went The Extra Mile - Engraving Etc. Forum

<body> <h1>Full Version: <a href="https://www.engravingetc.org:443/archive/index.php?webtag=EE&msg=4093.1">Xenetech Went The Extra Mile</a></h1><a name="a4093_1"></a><p><b>From: Jer (DIAMOND)</b> [<a href="lmessages.php?webtag=EE&msg=4093.1">#1</a>]<br /> 14 Jun 2006<br /><b>To: ALL</b></p> I needed a couple of extra fonts for my Xenetech XLE to reproduce 2 plaques a customer wanted done exactly as the old plaque. The rep said that was a font they usually sell when the machine is purchased. Apparently I did not buy that font. I told them never mind since it was for only one customer, I would figure something out. The rep told me to hold and he came back in in couple of minutes and said he would send the 2 fonts free of charge. Now I have 2 perfect plaques and a happy customer. Man it feels good to have that kind of support.<hr /><a name="a4093_2"></a><p><b>From: Ian (IANHR)</b> [<a href="lmessages.php?webtag=EE&msg=4093.2">#2</a>]<br /> 14 Jun 2006<br /><b>To: ALL</b></p> <p>I bought a used Xenetech when I figured my Meistergram 912 was on the way out, and a new licence and software, and because I have been using Engravelab, bought the driver for it from them too. Well, being what I am, the Xenetech gathered dust until this weekend when the Meistergram bit the dust big time right when I was about to start a large (to me) contract of aluminum door number plates with a logo on each one. No way do I have the smarts to learn a new software program in two days or even get the EngraveLab to run the table, but a couple of two hour phone marathons with Ben from Xenetech tech support and I'm back in business with a program I'm familiar with and a bigger, better machine. Don't ever underestimate the value of a software licence! Yess, they do go the extra mile.<br /> Ian</p><hr /><a name="a4093_3"></a><p><b>From: laserman (MIKEMAC)</b> [<a href="lmessages.php?webtag=EE&msg=4093.3">#3</a>]<br /> 15 Jun 2006<br /><b>To: Ian (IANHR)</b> [<a href="lmessages.php?webtag=EE&msg=4093.2">#2</a>] 15 Jun 2006</p> <p>Ian,</p> <p>What happened to the 912 perhaps I can help to fix it and you can use it as a back up.</p> <hr /><a name="a4093_4"></a><p><b>From: Ian (IANHR)</b> [<a href="lmessages.php?webtag=EE&msg=4093.4">#4</a>]<br /> 15 Jun 2006<br /><b>To: laserman (MIKEMAC)</b> [<a href="lmessages.php?webtag=EE&msg=4093.3">#3</a>] 15 Jun 2006</p> <p>Mike(?)<br /> The 912 developed a dreadful grinding noise on the uplift of the z axis, and I guess the added friction fooled the controller into thinking the spindle wasn't where it was supposed to be, so sometimes it wouldn't even touch the job and sometimes it drove itself right through it. I thought it might be the linear bearings, but after I replaced them (lucky find on eBay!) no luck. I took the motor down to a local repair shop and they wouldn't even touch it, so I took it apart and cleaned and it turned more freely, but still didn't work properly. So, I think it's the motor. It's a Vexta PH268-21 by Oriental motors and it's not made anymore. I'd love to get it up and running again because it really is a great little machine, so, let me know if you think there's some hope for it. <br /> Ian</p><hr /><a name="a4093_5"></a><p><b>From: Puck (PUCKERBRUSH)</b> [<a href="lmessages.php?webtag=EE&msg=4093.5">#5</a>]<br /> 15 Jun 2006<br /><b>To: Ian (IANHR)</b> [<a href="lmessages.php?webtag=EE&msg=4093.4">#4</a>] 15 Jun 2006</p> <p>Ian,</p> <p>If thats a Pro-Am 912 I might be able to tell you where to get a new motor. After mine started having problems I found places to buy parts and the motors are on my parts list that I found if I needed them to be replaced.</p> <p>Puck</p> <hr /><a name="a4093_6"></a><p><b>From: laserman (MIKEMAC)</b> [<a href="lmessages.php?webtag=EE&msg=4093.6">#6</a>]<br /> 15 Jun 2006<br /><b>To: Ian (IANHR)</b> [<a href="lmessages.php?webtag=EE&msg=4093.4">#4</a>] 15 Jun 2006</p> <p>Ian,</p> <p>I have several of those motors, I might question if that was the problem to begin with. It is very possible that the driver control board or the power supply is what caused the problem in the beginning. </p> <p>However once the stepper motor has been taken apart it is done it will never work properly again. You will need to replace the motor and then see if it was the motor driver or power supply that actually caused the problem.</p> <p>It is not a common item to fail on these engravers I would not say it is not possible but with my experience it usually is caused by the controller.</p> <hr /><h4><a href="lthread_list.php?webtag=EE">Back to thread list</a> | <a href="llogout.php?webtag=EE">Login</a></h4> <h6>© 2024 <a href="http://www.beehiveforum.net/" target="_blank">Project Beehive Forum</a></h6> </body>