Painting Heavy Brass - Engraving Etc. Forum

<body> <h1>Full Version: <a href="https://www.engravingetc.org:443/archive/index.php?webtag=EE&msg=6260.3">Painting Heavy Brass</a></h1><a name="a6260_3"></a><p><b>From: Stunt Engraver (DGL)</b> [<a href="lmessages.php?webtag=EE&msg=6260.3">#3</a>]<br /> 7 Mar 2007<br /><b>To: Josh (WIZURD)</b> [<a href="lmessages.php?webtag=EE&msg=6260.1">#1</a>] 7 Mar 2007</p> Josh,<br /> <br /> When using a card to squeegie excess paint from the surface, it's important to leave as thin a film of paint as possible.<br /> <br /> I've switched over to Citrisolve as my solvent of choice, for cleaning paint off the surface of a color-filled object.<br /> <br /> It loves making mush out of dried paint. :-)<br /> <br /> In fact, the drier the better, because semi-dry paint that comes into sufficient contact with the solvent will become liquid again, making cleanup more difficult.<br /> <br /> For large areas of engraving, wrap a clean, lint-free cloth around something flat and rectangular, like a piece of engraving stock and use the solvent on that, to wipe across the surface of the substrate. That will keep the cloth from <i>dipping</i> into the engraved areas.<br /> <br /> I've used Clay's syringe-fill method and it works very well. The only caveat is to make sure the paint fills the entire <i>well</i> created by the engraving. Otherwise, any areas along the top of the well, not covered by paint, will be noticeable and the edges of the letters will appear jagged.<p class="edit_text">EDITED: 7 Mar 2007 by DGL</p> <hr /><a name="a6260_4"></a><p><b>From: Andrew</b> [<a href="lmessages.php?webtag=EE&msg=6260.4">#4</a>]<br /> 7 Mar 2007<br /><b>To: Josh (WIZURD)</b> [<a href="lmessages.php?webtag=EE&msg=6260.1">#1</a>] 7 Mar 2007</p> <p>Hi Josh</p> <p>There are pens available for filling large letters (Flo-pens) that will minimise the amount of paint you get on the surface. I have tried many methods as I do this daily on small objects and small plates. </p> <p>having tried various ways, I tend to use the flood fill method and then use a rubber 'squeegie' that you use for grouting tiles etc to wipe the paint off the surface.</p> <p>This leaves a thin film of paint on the surface. I then wrap a lint free cloth on a block and put some cellulous thinners on the cloth, and wipe over the surface, or if the plate is small enough, I put some cellulous thinners onto a page of the Yellow pages and wipe the plate on the yellow pages. The yellow pages trick only works where I am using a single colour.</p> <p>If there is any paint still left, it comes off using a tiny bit of metal polish.</p> <p>I have only found the cellulous thinners available in specialist decorators stores - I find this excellent</p><hr /><a name="a6260_5"></a><p><b>From: laserman (MIKEMAC)</b> [<a href="lmessages.php?webtag=EE&msg=6260.5">#5</a>]<br /> 7 Mar 2007<br /><b>To: Josh (WIZURD)</b> [<a href="lmessages.php?webtag=EE&msg=6260.4">#4</a>] 7 Mar 2007</p> <p>Josh,</p> <p>What I used to do was slop the paint on and then take an old phone book squirt some lighter fluid onto a section usually covering a full page then after the enamel had dried for about 15 minutes run the plate over the phone book page soaked with lighter fluid. It pretty much removes most of the excess paint in one swipe across the book if you need more just turn the page and wipe again then just let it dry and wipe off the rest of the film.</p> <p>Now keep in mind I did this over 20 years ago and it worked pretty good back then.</p> <hr /><p align="center">Show messages: <a href="lmessages.php?webtag=EE&msg=6260.1">All</a>  <a href="lmessages.php?webtag=EE&msg=6260.1">1-2</a>  3-5</p> <h4><a href="lthread_list.php?webtag=EE">Back to thread list</a> | <a href="llogout.php?webtag=EE">Login</a></h4> <h6>© 2024 <a href="http://www.beehiveforum.net/" target="_blank">Project Beehive Forum</a></h6> </body>